地浸铀矿山浸出速度的影响因素

在地浸铀矿山生产过程中,铀的浸出速度是制约生产的重要参数,直接关系到矿山的服务年限。矿山生产采区往往存在严重的拖尾现象,为提高地浸铀矿山资源利用率,降低生产成本,研究了影响铀浸出速度的因素,提出了控制铀浸出速度的措施。     

A system for time-fluctuating flow rate measurements in a single-blade pump circuit

Commonly used flow rate measurement systems provide an accurate and stable output value of the quasi-stationary flow rate. In some pump types as e.g. single-blade pumps significant flow rate fluctuations may occur even in steady operation points due to rotor-stator interaction. For the analysis of the time-resolved flow rate a new measurement and evaluation method is presented based on an electromagnetic flow meter. Internal averaging of the flow meter is deactivated and the raw signal is evaluated directly with a sampling rate of 3 kHz. With ensemble-averaging in combination with an impeller position detection, interfering signals acting on the time-resolved measurement signal are filtered out. Accompanying numerical simulations of the pump flow circuit are carried out with a 1D method of characteristics and validated against well-established time-resolved pressure measurements of the pump flow. Experiment and simulation show a resembling trend of pressure as well as flow rate fluctuations over the entire operation range of the pump. Thus, by the combined utilisation of measurement and simulation technique, we assure the validity of the ensemble-averaged flow rate fluctuation results. We find that the flow rate fluctuations show a consistent phase shift to the pressure fluctuations that increases towards overload. The flow rate amplitude is an order of magnitude smaller than the amplitude of the pressure fluctuations.     

Crowding as an Agronomic Factor Determining the Development of Plants and the Productivity of Linseed (Linum usitatissimum L.)

ABSTRACT

Nine sowing densities of linseed were compared in a two-year experiment. Self-regulation of the density of a linseed stand resulted in a differentiated branching of the plants. The number of capsules on a linseed shoot, as well as seeds in the capsule, and the number of seeds from the shoot were highly varied from year to year, and there is even a stronger differentiation in the weight of 1000 seeds. Linear relationships were noted between the mass of seeds from the linseed plant and the number of capsules. The yield of linseed was affected by both factors. An increasing sowing rate reduced the seed yield from the shoot and the plant. At lower seeding rates, the lateral shoots contributed in the seeds yield of the plant to a higher degree compared to the main ones.     

基于Atmega16A单片机声发射监测系统的设计与应用

基于Atmega16A单片机自主设计一套地压监测系统。整个过程完成了硬件的购置、软件的设计、数据采集程序的编写、系统管线布置方式的设计以及系统的调试等工作。本监测系统的设计及装置的开发具有灵敏度高、功耗低,信号传输可靠、实时、远程和多元化数据监测,后期其他类型数据监测可扩展性强,系统成本低等优点。采集数据的声发射能率分析结果显示,有两次较大的声发射率值与监测范围内两次较大冒顶事故都可以很好的对应。希望该系统的应用能为矿山地下开采过程中地压活动的监测和预警提供技术支持。     

Air torque position damper hysteresis

The purpose of this paper is to determine the effect of the air torque position (ATP) damper hysteresis on the accuracy of air velocity measurements and the adequacy of the ATP damper mathematical model tested in the present study. A total of three dampers with non-cascading blades were examined: a damper with a single flat blade, a damper with two opposed flat blades, and a damper with two flat blades - one of which is a measuring blade and the other is fixed in the horizontal direction. Furthermore, a total of two damper installation locations in a duct system were examined as well: at the duct exit with a straight duct section preceding the damper and within the duct itself with straight duct sections both preceding and following the damper. The ATP damper hysteresis was found to exert a significant effect on the accuracy of air velocity measurements and the adequacy of the ATP damper mathematical model tested if the ATP damper is more open, i.e. with lower blade angles of attack. Moreover, the ATP damper installed at the duct exit was found to be more susceptible to hysteresis effects than the damper located within the duct.     

基于特征贡献率的机械故障分类方法

为了使7075铝合金薄壁件表面喷丸加工应力得到松弛和均化，运用ANSYS建立平台式振动时效有限元模型，通过振动模态和谐响应分析，获得最佳激振频率和试样装夹位置。在此基础上，将薄壁框架件置于平台上进行振动时效处理，以验证仿真分析结果，评价其对试样表面应力作用效果。结果表明：在亚共振频率为112 Hz时，试样在平台零振幅和最大弯曲位置处分别对称布置，时效后表面均形成应力松弛，松弛率分别为29.5%和33.3%，不均匀波动分别为20.3%和20.7%，而沿振动方向松弛程度不均匀，说明激振力造成了材料表面组织屈服，且屈服程度与应力强度有关。提出再时效-位置交叠方法，使应力松弛不均匀度分别下降到9.9%和15.9%，应力均化得到改善，该研究工作为薄壁类零件表面应力均匀化提供了参考。     

Proposal of novel chatter stability indices of spindle speed variation based on its chatter growth characteristics

Chatter is one of the most critical problems that causes poor surface quality and restriction of machining efficiency. Spindle speed variation (SSV) is a well-known technique for suppression of regenerative chatter. However, in the authors’ understanding, the chatter suppression effect diminishes when the spindle speed difference between the present and previous cutting moments is small. Furthermore, the stability changes largely according to the spindle speed variation profile which changes with the set condition of SSV parameters, e.g., nominal spindle speed, variation period and variation amplitude. Therefore, SSV parameters should be adequately set to avoid this limitation and to exert its effect throughout the entire duration of cutting. However, there is no clear methodology to determine the optimal condition. This paper presents the characteristics of chatter growth during SSV focusing on the change of chatter frequency, which lead to novel indices to evaluate the chatter stability when cutting with SSV. To verify the validity of the indices, time-domain simulations and the cutting experiments with triangular spindle speed variation (TSSV) are carried out. The influence of SSV parameters on the chatter stability is investigated from the simulation and experimental results. The limitations of widely utilized SSV profiles are discussed.     

Degradation rate quantification of solid oxide fuel cell performance with and without Al2TiO5 addition

Degradation rates of electrical current during constant voltage operation of SOFCs with anodes made using NiO precursor powders from two different manufacturers with and without the addition of aluminum titanate (ALT) added by either mechanical mixing or anode infiltration have been quantified using a novel MATLAB algorithm. Because the algorithm has been used to quantify degradation rates for many different SOFC tests, it is thought that the method can be applied to most measured SOFC data to quantify the instantaneous cell degradation rate as a function of time for the entire SOFC performance measurement. Degradation rates determined at different times have been plotted against varying concentrations of ALT addition, facilitating the estimation of optimum ALT concentration for SOFC anodes made with NiO from a specific manufacturer. The algorithm used to determine degradation rates is available upon request to the corresponding author.     

An approach to measure infill matric suction of irregular infilled rock joints under constant normal stiffness shearing

Rock joints infilled with sediments can strongly influence the strength of rock mass. As infilled joints often exist under unsaturated condition, this study investigated the influence of matric suction of infill on the overall joint shear strength. A novel technique that allows direct measurement of matric suction of infill using high capacity tensiometers (HCTs) during direct shear of infilled joints under constant normal stiffness (CNS) is described. The CNS apparatus was modified to accommodate the HCT and the procedure is explained in detail. Joint specimens were simulated by gypsum plaster using three-dimensional (3D) printed surface moulds, and filled with kaolin and sand mixture prepared at different water contents. Shear behaviours of both planar infilled joints and rough joints having joint roughness coefficients (JRCs) of 8–10 and 18–20 with the ratios of infill thickness to asperity height (t/a) equal to 0.5 were investigated. Matric suction shows predominantly unimodal behaviour during shearing of both planar and rough joints, which is closely associated with the variation of unloading rate and volumetric changes of the infill material. As expected, two-peak behaviour was observed for the rough joints and both peaks increased with the increase of infill matric suction. The results suggest that the contribution of matric suction of infill on the joint peak normalised shear stress is relatively independent of the joint roughness.